Tricky Circuit

An inverting operational amplifier

Amplify a signal and flip it

Op amp is short for operational amplifier: a powered circuit that amplifies the difference between two inputs. Negative feedback returns the output to the subtracting input. An inverting amplifier changes the signal sign; gain is output voltage divided by input voltage. Clipping means the requested output exceeds the supply limits. Av labels the linear voltage gain, in V/V: volts out per volt in, before clipping.

Open interactive experiment

EXPERIMENT BENCH

Change the circuit settings, predict the readings, then check a challenge. These are learning models, with the assumptions explained in each lesson.

Sign in to save progress. Guest progress stays on this device.

Open laboratory in a full window

How it works

Ideal amplifier powered at +5 V and −5 V; output is limited to these rails. No bandwidth, speed or current limits. Actual parts have other limits; this teaching model is not hardware tested.

Requested Vout = −Vin × Rf/Rin. Vin is input voltage, Rf feedback resistance and Rin input resistance. In the linear negative-feedback region, the subtracting input is near 0 V: a virtual ground, not a wire to ground. When clipped, that approximation fails. The input-current meter is source current through Rin, not current into the ideal op-amp terminal, which is zero. If clipped, Iin = (Vin − Vout)/(Rin + Rf), using actual Vout.

Difficulty
  1. Build · Observe

    Power on at input +1 V, input resistor 10 kΩ and feedback 20 kΩ. Read output −2 V.

    Need a hint?

    +1 V; Rin 10 kΩ; Rf 20 kΩ → −2 V

  2. Explore · Adjust

    At input +0.5 V, obtain output −1.9 to −2.1 V without clipping.

    Need a hint?

    +0.5 V; Rin 10 kΩ; Rf 40 kΩ → −2 V

  3. Solve it · Discover the limit

    At input +1 V, choose resistors requesting gain magnitude at least 6. Observe output clipped at −5 V.

    Need a hint?

    +1 V; Rin 5 kΩ; Rf 30 kΩ → requested −6 V, actual −5 V

Extra reading and circuit recipes

Amplify a signal and flip it

A useful connection

Doubling both resistors keeps gain unchanged but halves the input current while the amplifier stays linear.

A surprising detail

The output energy comes from the amplifier supply. Resistors set the gain; they do not provide that energy.

A useful trap to avoid

A virtual ground exists only with suitable linear feedback. A clipped amplifier cannot hold its subtracting input at 0 V.

Rf doubles, Rin stays fixed, and clipping is avoided. Gain magnitude…

  1. halves
  2. doubles
  3. stays unchanged
Read more

The magnitude is Rf/Rin, so doubling only the feedback resistor doubles it.

ti.com

Temu affiliate offers

Find your next electronics project

Explore these do-it-yourself project kits. Check the selected option, included parts and instructions on each offer.

Tricky Circuit may earn a commission if you buy through these Temu affiliate links. These are product ideas; they have not been bench-tested by Tricky Circuit and are not verified lesson parts lists.

Supplier photo of an assembled infinity mirror light cube illuminated on a dark background.

Supplier product photo

Build an infinity light cube

Listing specifies 5-volt direct current. Soldering required; battery and glue not included.

View kit on Temu

Supplier photo of a breadboard, jumper wires and assorted electronic components in a plastic storage case.

Supplier product photo

Try breadboard experiments

Breadboard, wires and assorted parts. Arduino controller board not included.

View kit on Temu

Supplier photo of an assembled blue surface-mount soldering practice board with a circular ring of small lights.

Supplier product photo

Solder a chasing-light board

Surface-mount soldering practice. Battery and battery holder not included.

View kit on Temu