Supplier photo of an assembled radio kit with a purple circuit board, telescopic antenna and clear case.
Supplier photo
Temu affiliate offer Ā· Project idea

Build a radio

Soldering required. Check the supplied parts and board revision.

View kit on Temu

Tricky Circuit may earn a commission through these links. Product ideas have not been bench-tested by Tricky Circuit and are not verified lesson parts lists.

ATtiny

Wiring tips to ensure your ATtiny (13/25/45/85) runs reliably in any project. šŸ¤–āš”

0

āœ… Must-Have Components for Stable Operation

ComponentPurpose
ATtiny MCUThe brains of your project šŸ§ 
Power Supply (3.3V or 5V)Stable voltage source from battery, regulator, or USB
0.1 ĀµF Ceramic CapacitorBypass capacitor between Vcc and GND for power noise filtering āš”
Reset Button (optional)To manually reset the chip (only if RESET pin is active)
10kĪ© Pull-Up Resistor on RESETPrevents false resets if RESET is not disabled via fuse bits
ISP Series Resistors (optional)~1kĪ© protection when programming ATtiny in-circuit

šŸ§© Basic Stable Circuit (ATtiny85 Example)

  • Use INPUT_PULLUP for buttons to avoid external resistors.
  • Keep the power lines clean and tight!

šŸ”‹ Power Supply Options

Power SourceNotes
CR2032 coin cellFor short-term portable use
Li-ion + LDO (AMS1117)Stable 3.3V output, good for sensors & WiFi
USB 5V (via regulator)Great for dev boards or breadboarding

šŸ“¦ Recommended Extras for Smooth Operation

ComponentWhy It Helps
10 ĀµF Electrolytic CapAdditional power smoothing, good for servos
Low ESR Ceramic CapFilters high-frequency noise
Perfboard or PCBAvoids flaky connections from breadboards

šŸ› ļø Optional Peripherals ā€” What to Add

PeripheralAdd This
LEDs220ā€“330Ī© resistors on each pin
ButtonsUse INPUT_PULLUP or external 10kĪ© resistor
OLED / LCDAdd 0.1ĀµF and 10ĀµF on Vcc near display
Servos / MotorsUse separate power + decoupling caps

šŸ“”Broadcast the signal ā€” amplify the connection.

You might also like

A current-limited low-voltage source feeds a 1 kiloohm series resistor and the LM4040AIZ-2.5/NOPB cathode pin 2. Anode pin 3 and unused pin 1 join ground; a selectable load and voltage meter are parallel branches across the reference.

LM4040: A Voltage Reference Needs a Current Budget

šŸ”„ The Ultimate Guide to Bed Adhesives for 3D Printing! šŸ›ļøšŸ–Øļø

šŸš€ Controlling an SG90 Servo with Arduino Using a Potentiometer and Buttons

Diode-free2Ɨ2 matrix: Pico GP10/11 rows, GP12/13 columns, independent10kĪ© pull-ups to3V3; A B C D normally-open switches connect row and column nets.

Pico Button Matrix: Make a Ghost Key Appear, Then Reject It

šŸ¤–šŸ”„ Letā€™s start with a simple robotic arm or leg movement using servo motors and an ATtiny85.

ATtiny85-20PU at 3.3 V: PB2 pin 7 reads lid contact, PB3 pin 2 acknowledges, PB4 pin 3 requests display, each with 100 kĪ© pullup. PB0 pin 5 drives a red LED through 4.7 kĪ©.

ATtiny85 Mailbox Flag: Remember an Opening, Then Sleep

Leave a Reply

Temu affiliate offers

Find your next electronics project

Explore these do-it-yourself project kits. Check the selected option, included parts and instructions on each offer.

Tricky Circuit may earn a commission if you buy through these Temu affiliate links. These are product ideas; they have not been bench-tested by Tricky Circuit and are not verified lesson parts lists.

Supplier photo of an assembled infinity mirror light cube illuminated on a dark background.

Supplier product photo

Build an infinity light cube

Listing specifies 5-volt direct current. Soldering required; battery and glue not included.

View kit on Temu

Supplier photo of a breadboard, jumper wires and assorted electronic components in a plastic storage case.

Supplier product photo

Try breadboard experiments

Breadboard, wires and assorted parts. Arduino controller board not included.

View kit on Temu

Supplier photo of an assembled blue surface-mount soldering practice board with a circular ring of small lights.

Supplier product photo

Solder a chasing-light board

Surface-mount soldering practice. Battery and battery holder not included.

View kit on Temu